Usually, bad IP assignment is related to VLAN's on the ports where the AP's are plugged in or incorrectly configured DHCP to the AP's, however as they are set with Static IP's, I guess it's not DHCP. 0 Kudos
Meraki MX84 Error Bad IP assignment configuration
Hi Team, MX84 reflects error of "Bad IP assignment configuration" through Broadband link configuration as WAN. Please suggest for fixation of issue. Thanks, Niraj
Meraki Go
The below image is a representation of what the message may look like in the Meraki Go app: This alert means a bad static IP or an incorrect VLAN tag with DHCP is being assigned to the Go hardware. Typically, network hardware will simply not work if you assign a bad IP address to it. Meraki Go hardware, however, will automatically switch back ...
Meraki MX Device getting Bad IP Assignment Configuration
I just replaced the ISP at an outer office. The new ISP plugged in their routers for phone/Internet. The Internet cable went into you MX64 device and started dishing out Internet and Network connectivity. When I went to check on the device online, I noticed the Bad IP Assignment Configuration message. Device is still working properly, dishing out the correct IP addresses for that office ...
Common Dashboard Alerts for Device Connectivity
Bad IP assignment configuration; Uplink IP address in conflict with another device; The device is using a DHCP IP address from VLAN X instead of using configured VLAN Y; 日本語(Japanese) If a Cisco Meraki device has issues with connectivity to the dashboard, the dashboard should show an alert.
Dashboard Alerts
This alert means a bad static IP or an incorrect VLAN tag with DHCP is being assigned to the Meraki device. Typically, network hardware will simply not work if you assign a bad IP address to it. Meraki devices, however, will automatically switch back to DHCP (automatic IP assignment) so that it can check in to the cloud and alert you about the ...
Meraki Go
Cisco Meraki MX Stagnativ IP assignment via Dashboard • Do4a.com; GR: Treat static IP assignment on the GB similarly on the GS. Try a laptop or phone - A laptop using the static INDUSTRIAL should be flourishing as well. If a laptop cannot use to IP mailing, or a phone, the Meraki Go hardware likelihood cannot use it as fountain.
Meraki Go
Meraki Go gear, though, will automatically switch back to DHCP (automatic IP assignment) so that it can check in to the plume and alerts you about the problem if along all possible. Of most common causes a this failed message are: That device features had a working static IP, but network changes have caused the IP address for become invalid.
If you want the IP to stay the same you can allocate a fixed IP address under the DHCP portion of the Security Appliance. If you want a truly static IP you need to make sure that address can reach the internet. A good test would be to give your own laptop the address, plug in via Ethernet and try to ping google (8.8.8.8).
Meraki Go
When there is an IP addressing issue, a Meraki Go device will attempt to find another working IP address via DHCP on other networks (or VLANs). The alert is caused when: A VLAN tag is set for DHCP, and DHCP IP assignment fails with that VLAN. An incorrect static IP is assigned to the hardware, and it reverted to DHCP as a backup.
Error: Gateway should not equal network ID when ...
Checked to make sure DNS was correct. Internet traffic is up and testing fine, but dashboard continues to say bad IP assignment even after configuration synchronized with Meraki. Static IP settings on the dashboard indicate MX WAN 1 is still pulling a local IP (192.x.x.x) and dashboard says "Bad IP assignment configuration".
Wireless Issue Resolution Guide
There is a high probability that one of these rules is blocking access to the local LAN. The best troubleshooting steps would be: Check whether the SSID is in NAT mode. If it is, navigate to Wireless > Firewall & Traffic shaping Rules > Layer 3 firewall rule access to Local LAN. If it is set to Deny, set it to Allow.
Source IP and/or VLAN mismatch on C9300X
I'm seeing "Source IP and/or VLAN mismatch" in the Event Log about every 30 minutes on the clock, and for the life of me, I cannot seem to understand where it is coming from. The switch is a member of a 2 member stack, where both MX'es in HA go into each member on port 24.
Meraki MX84 Error Bad IP assignment configuration
Hi Team, MX84 reflects error of "Bad IP assignment configuration" through Broadband link configuration as WAN. Please suggest for fixation of issue. Thanks, Niraj
Meraki Go
An explanation on Bad Internet connection for Meraki Go hardware, and what troubleshooting steps to take. Overview This alert indicates the connection to the internet is not working as expected.
Z3C (Disabled gateway bad connectivity)
Solved. Sep 27 2021 3:03 AM. My company has recently set up over 150 units of Z3C's across the country, and in some destinations we get these messages 'Disabled gateway bad connectivity'. Now in the example above, it's a bit weird since the signal strength is good (3 out of 5 lines), and the speed in general is like 50down and 15up, so it's not ...
Re: Removing Network from Template Issues
The actual unbind post request gets returned for 400 (Bad Request) From my understanding with talking to support there is not a configuration retention issue preventing the unbinding, but a known sync issue with dashboard that is still unresolved for a number of networks.
Re: Bad IP Assingment
Technical Forums; Groups. API Early Access Group; Cloud Monitoring for Catalyst - Early Availability Group; CLUS 2023 Meraki Lounge; New to Meraki User Group
ダッシュボード接続に関するアラートについて
Bad IP assignment configuration. Cisco Meraki デバイスに対して固定 IP アドレスをダッシュボードから、または my.meraki.com ＞＞ Uplink configuration ページ経由で設定した後に、ダッシュボード上では "Bad IP assignment configuration" と表示がされる場合があります。
Re: DHCP Lease
As the client has already been given an IP address, it will typically hold onto it until expiration. It would be up to the client to request a new IP from the DHCP server. Most operating systems will support this in one way or another but you'll need to log onto the client directly.
Re: Port STP change designated→disabled; Port status change old: 1Gfdx
Vince, did Meraki ever get back to you with a solution to this in a firmware fix. We are no experiencing similar behaviour with our IP Telephones, Cisco 8851's. We are using MS250's with 11.22 firmware. I am considering disabling the LLDP on the phones per your post to see if this helps.
Solved: Re: Get Request for Multiple Sites
Yeah that's it. Need to pull the DHCP reservations (Fixed IP address assignment as Meraki call it) across all the networks in the org. Customer has 50+ sites, and wants a report for all sites. I can do it for 1 site no dramas, but pulling it for the whole org is proving a bit more difficult. Keen to hear how it can be done.
COMMENTS
Usually, bad IP assignment is related to VLAN's on the ports where the AP's are plugged in or incorrectly configured DHCP to the AP's, however as they are set with Static IP's, I guess it's not DHCP. 0 Kudos
Hi Team, MX84 reflects error of "Bad IP assignment configuration" through Broadband link configuration as WAN. Please suggest for fixation of issue. Thanks, Niraj
The below image is a representation of what the message may look like in the Meraki Go app: This alert means a bad static IP or an incorrect VLAN tag with DHCP is being assigned to the Go hardware. Typically, network hardware will simply not work if you assign a bad IP address to it. Meraki Go hardware, however, will automatically switch back ...
I just replaced the ISP at an outer office. The new ISP plugged in their routers for phone/Internet. The Internet cable went into you MX64 device and started dishing out Internet and Network connectivity. When I went to check on the device online, I noticed the Bad IP Assignment Configuration message. Device is still working properly, dishing out the correct IP addresses for that office ...
Bad IP assignment configuration; Uplink IP address in conflict with another device; The device is using a DHCP IP address from VLAN X instead of using configured VLAN Y; 日本語(Japanese) If a Cisco Meraki device has issues with connectivity to the dashboard, the dashboard should show an alert.
This alert means a bad static IP or an incorrect VLAN tag with DHCP is being assigned to the Meraki device. Typically, network hardware will simply not work if you assign a bad IP address to it. Meraki devices, however, will automatically switch back to DHCP (automatic IP assignment) so that it can check in to the cloud and alert you about the ...
Cisco Meraki MX Stagnativ IP assignment via Dashboard • Do4a.com; GR: Treat static IP assignment on the GB similarly on the GS. Try a laptop or phone - A laptop using the static INDUSTRIAL should be flourishing as well. If a laptop cannot use to IP mailing, or a phone, the Meraki Go hardware likelihood cannot use it as fountain.
Meraki Go gear, though, will automatically switch back to DHCP (automatic IP assignment) so that it can check in to the plume and alerts you about the problem if along all possible. Of most common causes a this failed message are: That device features had a working static IP, but network changes have caused the IP address for become invalid.
Technical Forums. SASE / Secure Connect; Cellular Gateways; Security & SD-WAN; Cloud Security & SD-WAN (vMX) Switching; Wireless; Mobile Device Management
If you want the IP to stay the same you can allocate a fixed IP address under the DHCP portion of the Security Appliance. If you want a truly static IP you need to make sure that address can reach the internet. A good test would be to give your own laptop the address, plug in via Ethernet and try to ping google (8.8.8.8).
When there is an IP addressing issue, a Meraki Go device will attempt to find another working IP address via DHCP on other networks (or VLANs). The alert is caused when: A VLAN tag is set for DHCP, and DHCP IP assignment fails with that VLAN. An incorrect static IP is assigned to the hardware, and it reverted to DHCP as a backup.
Checked to make sure DNS was correct. Internet traffic is up and testing fine, but dashboard continues to say bad IP assignment even after configuration synchronized with Meraki. Static IP settings on the dashboard indicate MX WAN 1 is still pulling a local IP (192.x.x.x) and dashboard says "Bad IP assignment configuration".
There is a high probability that one of these rules is blocking access to the local LAN. The best troubleshooting steps would be: Check whether the SSID is in NAT mode. If it is, navigate to Wireless > Firewall & Traffic shaping Rules > Layer 3 firewall rule access to Local LAN. If it is set to Deny, set it to Allow.
I'm seeing "Source IP and/or VLAN mismatch" in the Event Log about every 30 minutes on the clock, and for the life of me, I cannot seem to understand where it is coming from. The switch is a member of a 2 member stack, where both MX'es in HA go into each member on port 24.
Hi Team, MX84 reflects error of "Bad IP assignment configuration" through Broadband link configuration as WAN. Please suggest for fixation of issue. Thanks, Niraj
An explanation on Bad Internet connection for Meraki Go hardware, and what troubleshooting steps to take. Overview This alert indicates the connection to the internet is not working as expected.
Solved. Sep 27 2021 3:03 AM. My company has recently set up over 150 units of Z3C's across the country, and in some destinations we get these messages 'Disabled gateway bad connectivity'. Now in the example above, it's a bit weird since the signal strength is good (3 out of 5 lines), and the speed in general is like 50down and 15up, so it's not ...
The actual unbind post request gets returned for 400 (Bad Request) From my understanding with talking to support there is not a configuration retention issue preventing the unbinding, but a known sync issue with dashboard that is still unresolved for a number of networks.
Technical Forums; Groups. API Early Access Group; Cloud Monitoring for Catalyst - Early Availability Group; CLUS 2023 Meraki Lounge; New to Meraki User Group
Bad IP assignment configuration. Cisco Meraki デバイスに対して固定 IP アドレスをダッシュボードから、または my.meraki.com ＞＞ Uplink configuration ページ経由で設定した後に、ダッシュボード上では "Bad IP assignment configuration" と表示がされる場合があります。
As the client has already been given an IP address, it will typically hold onto it until expiration. It would be up to the client to request a new IP from the DHCP server. Most operating systems will support this in one way or another but you'll need to log onto the client directly.
Vince, did Meraki ever get back to you with a solution to this in a firmware fix. We are no experiencing similar behaviour with our IP Telephones, Cisco 8851's. We are using MS250's with 11.22 firmware. I am considering disabling the LLDP on the phones per your post to see if this helps.
Yeah that's it. Need to pull the DHCP reservations (Fixed IP address assignment as Meraki call it) across all the networks in the org. Customer has 50+ sites, and wants a report for all sites. I can do it for 1 site no dramas, but pulling it for the whole org is proving a bit more difficult. Keen to hear how it can be done.